Jump to content
SAU Community

Recommended Posts

i was just wondering if you could convert the parking lights.... these ones:

parkers.jpg

into blinkers.

ive got an aftermarket bar that will need aftermarket blinkers that i dont really want to drill onto the bar.

i know you could just cut and connect the wires up, but is there anything else to it?

is the bulb in the parkers able to take the voltage of the blinker lines?

Edited by SECUR1TY
Link to comment
https://www.sau.com.au/forums/topic/98792-convert-park-lights-into-blinkers/
Share on other sites

It should be same voltage. If I don't see the current draw to be too high for the sockets etc either.

Re-wiring should be easy since you are going to be left with dangling blinker wires after your new front bar goes on...

Just remember to get orange blinker bulbs :P

Damn! I was thinking of doing this for the last few months. =-]

I thought the easiest way was to rerun the blinker wiring up to the parker socket, then soldering or crimping the blinker wire onto the parker globe socket.

That way, you don't need to worry about the current-draw, cause i'm sure the parker socket isn't going to be rated any differently to the blinker socket. All the lighting should be 12 volt, as has been said by "cc".

shouldn't be man. The blinkers usually run off a relay, which will blink double-speed if one of your other indicators isn't working.

Well, in my previous non-Nissan cars, that's how it worked. Usually the rear one was water-logged if the front one was going double-speed.

Interesting to find out if that is the case or not!

You will need to use orange bulbs or else its a defect.

But if your removing park lights, it will be a defect anyway.

When you get a rego check done, they will probally fail your car if its missing lights such as parkers.

So be warned...

drill a hole into your plastic housing and insert a clear white LED, then wire the LED in with a resistor to the park light connection. Instant parklight. You can then use the existing parklight as an indicator with an orange globe (or a clear globe that lights up orange).

we I have done this to my R33 2 years ago as the crapy trailer blinkers on the front bar looked sh!t, so put driving lights in the holes. moved the blinkers to the parking lights just rewire the the parker wires withthe blinker wires and change the wedge bulb with a orange glob!.....presto!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not noticeably. Arguably, the catless turbo is going to work harder in a different direction, as it will spool up faster, go to higher speeds more easily. Only if it was tuned in the original condition. If it was a stock tune, using the AFM before and after the cat/dump change, then no, no retune needed. If the car is running on a MAP sensor, then it might well benefit from a retune. It might even run a little dangerously without a retune, but it could quite easily be fine.
    • We had this blend that uses 98RON + 10% Ethanol which brought it to 100RON. It's no longer available anymore unfortunately.
    • Does it make a difference in your turbo having a shorter life if you have a cat converter as it causes that back pressure versus less/no back pressure with a decat? (Not sure if this is accurate) Also slightly different question if you went from a oem cat to a decat or vice versa will it require a tune? I heard if you change the dump pipe onwards it requires a tune?
    • No. Have only gotten as far as contemplating the task of having to put in the required fairly heavy wiring and fusing to run it (along with the big alternator), and preferring not to. But otherwise, it would be nice to have a little extra freedom as to exactly where the compressor is located and free up some space around the exhaust side of the engine.
    • Following from this in a related by not closely-related sense... Because I was buying a bunch of other GKTech stuff, I got some rear subframe collars. The history that leads up to this is: 25+ years ago the car arrived into the country with stock subframe bushes. At some point shortly thereafter I added Whiteline pineapple rings, set up neutral, and it improved the rear end behaviour. Well, it is my vague memory that I was happier with it with them in. Less axle tramp on launches, generally better, etc etc. ~2012 it got a new non-HICAS subframe with new stock bushes. No pineapple rings. I reckon that ever since then I've been dissatisfied with the axle tramp. Recently I've been f**king around a lot with all aspects of the suspension. One contemplation has been to relocate the rear lower control arm front mount points (and do the other things needed to make that work) to improve longitudinal rear grip by getting rid of some of the stupid anti-squat that Nissan ladled into the R32. But.... before doing that I thought I'd put some collars in. And.... The collars are good. The rear sounds a little bit different, but there has been no significant increase in NVH coming up into the body. In terms of rear behaviour - expansion joints on long sweeping elevated freeway ramps that would sometimes cause the rear to jiggle around a bit, no longer seem to do so. It appears that jamming chunks of metal into the gaps in the rubber so they can't move much is a really good thing. And the launch behaviour and general forward traction situation seems to be greatly improved too. It's impossible to be really sure, because the tyres are completely shagged - they are freakishly willing to let go right now. But as an A-B test with the same tyres it certainly seems to grip up a lot better. Highly recommended to anyone who still has stock bushes.
×
×
  • Create New...