Jump to content
SAU Community

Installed R34 Eyelids

satanic

By satanic,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

FILO34 Proficient

FILO34

Posted
Posted
For some reason the nismo ones just don't do it for me, they look more agressive thats for sure, and looks like you did an awsome job installing them, but as wink said they don't cover enough of the head light.

I reckon one of these two could be the go for me

eyeline-up.jpg

fb2.jpg

Pics of eyelids the above are C-West item.

I dont reckon that those C-West ones dont really look

as tuff though. I reckon front ends of the R34 would look

good if all parts suit each other and go well together.

Such as the that C-West R34 (2nd pic) that suits better

then the 1st pic. But i guess eveyone is differnt, everyone

has differnt taste to suit there style.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32GTR R200 reverting from Nismo centre to stock

      By MBS206 · Posted

      But it's much better to use a freedom unit that has four different possible meanings...
    • GTSBoy
      R32GTR R200 reverting from Nismo centre to stock

      By GTSBoy · Posted

      Or a useable metric unit?
    • joshuaho96
      R32GTR R200 reverting from Nismo centre to stock

      By joshuaho96 · Posted

      I would try messing with friction modifier to see if it smooths it out.  Just keep adding more until it stops chattering or grabbing quite so much. If you haven't changed the gear oil in a long time you may as well start there too in case that has anything to do with it. You might want to also verify the initial torque is set to the lowest setting too. Requires popping out one of the CV axles first but that's not too bad. Once you're sure the preload is set to the lowest you can try adding an ounce at a time of friction modifier until it feels right to you.
    • djr81
      R32GTR R200 reverting from Nismo centre to stock

      By djr81 · Posted

      It is possibly 55 degrees for the Nismo version. I had a look through the manual and the stocker has a breakaway torque of 2.5 to 3.5kgm. Supposedly the Nismo LSD goes down to 5kgm when worn in but it is pretty grabby even with very little throttle. Worse when cold. So I guess you have three things. 1. Shims. 2 Friction plates 3. Cams Would think shims would be the easiest but Ive no clue how many tenths of a mm shim thickness change equals how many kgm torque. Also not sure if the Nismo friction plates are similar/different to stock or if they are the most of the source of the diff being angry. Think I can write off the Nismo rebuild kit for the standard diff as not being what I want.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it was a bit of confusion with me, I rang and asked if they had a boot for a soft top, and then the paint shop when they rang and were asked if it had a hard top on it, which it does, just not a PRHT....LOL Meh, whilst frustrating for all concerned it isn't a war stopper and should be a thing of the past in a week or two In other N/A related news, car is booked in at the end of the month for the cams, springs, retainers, harmonic balancer and retune  I might even pull the lazy arse card and get them to do a full service on it whilst it is there
×
×
  • Create New...