Jump to content
SAU Community

Recommended Posts

Hi people

I've got an rb20 running of a microtech lt 12 and was wondering if the O2 sensor was needed to be connected.Cause at the moment it aint. the wire's cut from the microtech cause at the moment I'm gettin really shitty fuel economy and i was wondering if i put in the O2 Sensor would it make a difference?? At the moment it does backfire a fair bit.

Also my car's making 241.3 awkw but it's running a little lean up top goes to about 12.6 on 16psi, my car has got all the fueling mods like. Walbro 500hp fuel pump and GTR injectors which have not reached 100% duty cycle. i was wondering if there are any ideas why it might be running a little lean and up top. I'm going to change the fuel filter soon, could it be that??? On 14psi it's runnin like a dream with a very safe Air fuel ratio of 11.9 to 1 so any ideas to get the car to run richer up top would be good so i can wind more boost into it.

any help would be great

Cheers

anthony

Edited by black sky
Link to comment
https://www.sau.com.au/forums/topic/98964-o2-sensor/
Share on other sites

Microtech does not use O2 sensor as it does not have closed loop function.

You can hook it up for display purposes only.

Unless you finely tune every load point/cell on the microtech you will have bad economy because of the lack of closed loop on this ecu.

Its the biggest downside of Microtech and why most people avoid them like the plague.

Link to comment
https://www.sau.com.au/forums/topic/98964-o2-sensor/#findComment-1802230
Share on other sites

you beleived wrong mate.

http://microtechefi.com/html/LT16.htm

User definable auxilliary input and output functions enabling such functions as traction control and self - tune.

Wide band Oxygen sensor input and 45psi map sensor standard issue.

:)

Link to comment
https://www.sau.com.au/forums/topic/98964-o2-sensor/#findComment-1808895
Share on other sites

No - Simply putting an O2 sensor on a car wont make fuel consumption better. Your ECU must have closed loop function to trim fuel up or down. And as for microtech and Auto tune function - wouldn't rely on it. Have not seen any of the cheap ECU do auto tune very well at all.

Link to comment
https://www.sau.com.au/forums/topic/98964-o2-sensor/#findComment-1812207
Share on other sites

it's an ECU designed for racing, meaning to get good fuel consumption you will have to tune ALL load points, rather well too.

was speaking to a mate who has an R33 with 250rwkw and a microtech and he's getting around 250km to a tank

Link to comment
https://www.sau.com.au/forums/topic/98964-o2-sensor/#findComment-1813385
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As I implied in my post, I have NO idea what the were. But in case I didn't make it clear, the way they performed was brilliant; whatever the brand was. I think it was the compound that made the difference. And if they were Bendix, then sign me up, I want another set. I did drive down mount Ousley (just outside of the Gong) a few times, and they showed no untowards performance.   Its not the low dust that I am looking for NOW. At the time I needed low dust, but now I have no issues with dust but want the initial/early bite of the pads that were used. Yeah, the early cold squeal may of been due to a missing shim or such.  And to repeat, its not the low dust I am seeking, its the initial bite of the pads and increase in bite as  the warmed up during each breaking. As soon as I let off, I don't remember the breaks being extra sticky if I used them again soon after. But I also did not test that theory.   Thanks for the recommendation, But I would prefer to choose something specifically with the behaviour I described.   I assume that they didn't use the default compound off the shelf, as we discussed the dust issue at length. And the early squeal when cold, I have seen the sound is more of an issue with some pad compounds. Mostly ceramic, which also are said to produce less dust.
    • Well, in 2007 he must have been charging about $1800 an hour. He only looked at the car for 5 minutes. And another 4 to write the report wrong, and another minute to correct it. Mind you, this was for a car that was: Stock engine, fmic (hole in drivers guard), all alloy intake and custom air box, 3 inch turbo back exhaust, lowered, and a set of 17" Advans (255/40/17 rear and 235/45/17 front). It was nothing crazy. The blue slipper wanted the "hole in the guard" engineered. But that was because he got the shits that I wouldn't "relocate the battery from the boot, back to the factory position in the engine bay"... In an R33 GTST...     Also for emissions, E85, and don't go wild on timing. It's amazing how the closer you get ignition timing towards max torque, the last couple of degrees really throw NOx counts right up. And for the huge increase in emissions, it's only a small increase in torque.
    • He'll be looking down and swearing about "the damn apprentice" for trying to convince Duncan to use percussive maintenance... 😛  
    • I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
×
×
  • Create New...