Jump to content
SAU Community

Recommended Posts

how r ya guys! just had the 32 dyno'd 2day. it only has an exhaust, injectors(the comp has been played with 2) and r32gtr ball bearing turbos i think. i thought it was running fairly stock but it surprised me pulling 204.3 four wheel kw's. at 12psi. it was a shock 2 me. but im stoked!! i was expecting 180-190 four wheel kw's

i know alot of u guys got cars that has heaps more power! im happy

Link to comment
https://www.sau.com.au/forums/topic/99244-had-my-32-gtr-dynod/
Share on other sites

i went to Turbo Tune on south road, they have a 4wd dyno set up. umm, i think the cost was round $60-$70 for a power run and print out of it, i had a service as well that day.

i rekon they got up to a 50/50 split, the tourqe guage goes up there, but im not 100% sure! i thought they had the same attessa-ets system as the gts-4

i rekon they got up to a 50/50 split, the tourqe guage goes up there, but im not 100% sure! i thought they had the same attessa-ets system as the gts-4

ye i assumed they have

i call my GTS-4 a baby GTR i will have to go and see them in the new year

ye i believe they run diff diff ratios but r u guessing there alot stronger ie different axels or u have it on good authority

i cant see nissan developing heaps of different parts for the 3 main kind of variety of skyline

yeah ur right mate...slippin or g-force i reckon causes the front diff to engage. when i boost the torque guage goes up, when i got ova a bump i guess sencing lose of traction and yeah in the wet

Wait.. I thought GTR's were RWD cars unless the rear wheels begin to slip? Say, with ATTESSA you have a 100% RWD car, but if you start sliding around on gravel the front wheels bite, up to 50% or something like that?

no i think thats wrong there constant AWD

i should of looked first

The ATTESA E-TS system an electronically controlled all wheel drive system.

Edited by Madaz
how r ya guys! just had the 32 dyno'd 2day. it only has an exhaust, injectors(the comp has been played with 2) and r32gtr ball bearing turbos i think. i thought it was running fairly stock but it surprised me pulling 204.3 four wheel kw's. at 12psi. it was a shock 2 me. but im stoked!! i was expecting 180-190 four wheel kw's

i know alot of u guys got cars that has heaps more power! im happy

i didnt think that r32 GTRs had ball bearing turbos.... only ceramic or N1 steel wheel

ok well i have observed while owning and driving a r32 gtr that just normal driving the torquesplit guage sits on 0% font 100% rear, start to accelerate, wheel spin or loss of traction and the guage starts to increase. depending on the circumstance, determines the amount of torque that is split. going by what i have seen in my gtr!!

Atessa works by G-FORCES. There are g-force sensors throughout the car so for example when it feels sudden acceleration etc it will start transferring power even without loss of traction.

That dyno result is good and is about the normal for those mods. I have done 226kw at all 4 with exaust, power fc but running 1 bar, so your car is on the money!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you are genuinely considering trying to get this engineered, I would strongly advise finding the engineer that is happy to sign that off first before you put the hole in your car.  I've seen cars get defected for this and not be able to be put back on the road as no engineer they spoke to was happy to sign if off.  
    • Apologies, while id like to put the MAF as close to the TB and relocate the recirc, this may be too much work. Will most likely end up just putting it on the original AFM spot ( onto/next to the airbox ).  Was going through nistune, found a pretty nifty doc on this. Nistune MAF Notes. Also, i was looking through the bay, and there seems to be a tube/line connected from the A/C to the intercooler piping ( Between the smic and the recirc), what does this do as the crossover fmic piping doesnt have any connection? plumbing? not sure what you call it but the nipple thing ahah.  Also, been reading up more about crossover fmic in regards to the legality of having the hole drilled for the piping, this would most likely need to be engineered right?
    • My advice is if you need a big build done do it in Japan. The yen rate is so favorable and there are shops that can be genuinely trusted and not micromanaged/carefully monitored every step of the way. Garage Yoshida is obviously my preferred option but they're so busy these days and all interaction with new customers has to be mediated through BBL/Toprank now. 
    • I haven't....but a poorly made one would terrify me. Surely a good second hand one is the go, as they don't work hard and no-one wants to keep one after they are finished with it A big consideration would be the weight of the shell you are putting on it....is it a fully dressed chassis or just the body
×
×
  • Create New...