Jump to content
SAU Community

Recommended Posts

This mite be a stupid question but as far as i know the V8 supercars use a spark plug near the end of their exhausts to create the fire you see out the back...i think this is there so it creates some sort of back pressure or something like that...

i guess wat i'm asking is if we were to place a spark plug near the end of our exhausts wouldn't that cause a pull of air through the turbo on gear changes keeping it spinning.

i'm not looking to do this for the rice factor just interested if it would work and how i wud go about doing it.

also would there be a way to turn it on and off.

thanks for any feedback...also be nice with replys i'm learning still.

cheers, Mark

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/
Share on other sites

you can use aftermarket 3rd party tools to help assist with turbo lag and "spooling up" if this is what you are referring to? I suggest you do a search on anti-lag. the idea is to retard the timing and dump fuel on gearchange to keep the exhaust housing spinning and so when you come back on throttle the turbo is still spinning at a higher speed that it would have been when you back off throttle the normal method. the result well in theory is not as much lag as the turbine is still running at a high speed, enough to bring the compressor back into its efficiency zone quickly

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1817534
Share on other sites

Back pressure is not something you want in a turbo setup. That will increase lag, not decrease it.

So, logically speaking, if the V8 Supercars were igniting fuel in the exhausts to generate back pressure...it would be counter productive on a turbocharged car. It wouldn't "pull air" through the exhaust - it would just block it.

Of course, as people have said above its not the case. You can blow flames just as easily in your car by pulling out your cat and running non-baffled mufflers. Just rev the car hard and pop off the gas.

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818662
Share on other sites

A fair few pro off-street race cars will run anti-lag. Most involve dumping excess fuel on throttle-off (normally by running it rich and taking timing out), and will either use a spark plug in the turbo's exhaust housing or rely on the hot turbine itself to ignite the fuel.

Normally they'll use an aftermarket ECU, so you can program and choose what conditions you want the anti-lag to kick in.

Aside from being very street illegal, you have to be a pro racer to run such a setup since your turbocharger then becomes a consumable. There's few faster ways of f**king your turbo's wheel than causing explosions on them.

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818665
Share on other sites

like i said it was just someone telling me they had been wondering about it who maybe doesn't know much at all. ohwell was worth asking...i didn't think it sounded right hence the "be nice with ur replies" part

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818870
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • My take on gg2 48mm, 54mm, 58mm, and 62mm compressor map for same size compressor vs gg1 : All gg2 only outflow gg1 above 20 psi. As all g gen 2 surge line at lower left of comp map move to the right, all gg2 sacrifice spool vs same size gg1, surge line move to the right worst for 54mm gg2. So for same size compressor if you want best response, use gg1, if you want max hp at >20psi use gg2 but you will be laggier vs same size gg1. Max compressor efficiency drops to max 75% on all gg2 vs max 76%-80% of same size gg1. Iirc lower efficiency means hotter iat less dense air so lower hp at same operating point of comp map. Also curious why gg2 is mapped to lower max rpm vs same size gg1 (only 48mm size both gg1 gg2 mapped to same rpm) : 54mm gg1 165,000 rpm  vs  gg2 160,000 rpm. 58mm gg1 150,000 rpm vs gg2 140,000rpm. 62mm gg1 145,000 rpm vs gg2 140,000 rpm. If gg2 can safely spin to gg1 rpm then they can flow a bit more than as mapped. Good thing that all gg 2 interchange compressor and turbine housings with same size gg 1. So gg1 owners can buy gg2 chra only if planning to boost >20psi.
    • My stuff is all with Shannon's, granted, I don't really have imports I'm driving on the road, however, I've had multiple cars at the same time with them. Presently we have the Landcruiser on laid up cover, Sarah's Kluger on full cover, and the house insured. About 18 months ago Sarah wrote her Subaru Liberty GTB off, insured with Shannon's, and the payout, and buy back of the wreck was super quick. In 2020 we had the VF Commodore totalled in a major hailstorm. Storm was on the Saturday, I called on the Sunday and lodged it, vehicle was towed on Tuesday night, assessment team called on Wednesday to say it was a total loss and get payout details, money was in the bank on Thursday morning. Have had a few other claims both at fault, and not at fault, over the years, and never had an issue with them.   Funnily enough, they're also the cheapest insurer I find for things like Sarah's Kluger.   I will say I'm less impressed dealing with them lately around "the experience", as a lot of their staff that you deal with aren't car enthusiasts. Shannon's has a much more main stream feel ever since they decided to become "big corporate", laid a heap of staff off, and then hired a bunch of non enthusiasts. At the same time they've been making a push to be less "call us and we'll personally have someone who cares help" to "hey, this computer can do stuff for you" and are trying to get more square pegs to fit round holes. (That's just the vibe I get from them). Again, have had no issues with claims with them, but get a bit of a "less personal" feel from them.
    • A thing I wasn’t happy with with enthusiast was during the initial phone call they told me they’d insure it for 130k but needed photos.   I then sent them photos and they told me $80k as there were other cars either similar modifications available for around that price, I told them to send me the links to said cars so that I can buy them. i then sent the modification list with prices of the parts (no labor) and the price then came to 115k, which is still shy of the 130 that was agreed in the initial phone call 
    • Ask me a bit later this week before payday
    • I agree that delayed payment probably isn't the most suitable solution. It seems a solid complete transaction would be best. As I wouldn't be using this sale as a line of credit that would typically earn interest, we can probably arrange a much cleaner single transaction deal. I can do $92.52 today. Would you prefer EFT, or Cash on Pickup?  😛
×
×
  • Create New...