Jump to content
SAU Community

Recommended Posts

im really interested to start drifting for a sport i would like some info on how to get into it like:

do you need a cams license?

do you need to be a member of a club?

what fees are required to get on the track?

how often do drift events happen?

what would be the first mods to a car with a minimal budget?

thanks for your imput let me know if this has been covered before

Link to comment
https://www.sau.com.au/forums/topic/99932-whats-needed-to-get-into-drift/
Share on other sites

1: yes cams licence is needed, in adelaide its an S2 cams licence not sure on other state could be same name........i assume it would.

2: generally its cheaper to drift as part of a cams affiliated club and you'l get notified on more events as well

3: Not sure on other states, but fees in adelaide are as follows

- $85 cams licence

- $140 to enter your car per event

- $$$ tyres

- $$$ fuel

- $ club fees if any

- $110 or something for practice at mallala and $20 for day pass cams licence (strictly once off, second time practice ur required to have ur cams licence)

4: Theres quite a few drift events now varying between states and National. 2 National events now, and each state has its own drift event seperately.....so if your good enough ur car and urself will get a good workout if u try for all 3

5: mods for a car with minimal budget could be many things

- catback exhaust system

- air pod

- front mount intercooler

- fuel cut defender

- turbo if the moneys there

- BOV (keep that standard turbo running)

- oil cooler (very important)

- good coilovers

- adjustable camber arms front and rear

- adjustable castor rods front

- 2 way mechanical diff (very important cant stress that enough)

- Hicas lock bar if your car has hicas steering

Heaps mate, pm me if u want more details

1- Just to add you won't need a cams license if you're just practicing at private track days like Fatz or something like that, although it's generally a good idea.

2- Similarly you don't absolutely need to be a member of a club (atleast not the first few times you go out drifting) but I think it's generally a good idea to support the scene that supports you. As I said it's generally a good idea to get a cams license and to get a cams license you need to be in a club that is affiliated with cams.

SAU is cams affiliated and cheap - cheapest club in NSW that is cams affiliated as far as I know.

To get started I'd say you need a FR car that you can give the beans. I'd question if you really need a pod though :huh:

5-

Car mods with absolute minimal money IMO

- suspension bits

- diff

- oil cooler

- get rid of hicas

Then

- exhaust

- replacement air filter

- boost controller + front mount (if turbo)

-

The list above by Nathan is pretty much where you'd want to be to start at a semi pro level (imo). If you've never done it before you could gradually build it up. Be mindful that's not even talking about power mods.

You also need a helmet.

try a motorkhana or two first. They cost a lot less than $140 - in QLD a round of the QLD motorkhana series costs about $20 to enter! and you'll get all the sideways fun you can handle in a very safe envirnoment. It will definitely improve your car control and give you more confidence before you start drifting at higher speeds on the track. And you don't need any mods.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And the full R32 GTR wiring diagrams are also freely available. Hmm.... there's supposed to be an auto replace that would have linked the thread. Here it is, manually  
    • Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
    • I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I’ve been super cautious, did a lot of research, and took my time. I’ve driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times—no issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It’s not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test—belt isn’t too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it’s slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it’s just how it sits? I’m probably overthinking this, but since it’s my first time doing this on a NEO and the engine is forged, I really don’t want to mess anything up.   Also, I’m thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there’s a real difference between the two.   Any advice or reassurance would be much appreciated!
    • 40 grit sounds about right, to start. You make some decent cuts/damage in the coating with that, then rapdily scale up to maybe 80 and 120 for the bulk of the actual removal, then fine it off to 180 or 240 perhaps. No need to go any finer than that, and maybe no need to go even as fine as that. Wrap it on a big block and have at it. At least on the hub face.
    • Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes. Traction is going to be at a premium!
×
×
  • Create New...