Jump to content
SAU Community

Rb25 Heads

25GTV

By 25GTV,
in Engines & Forced Induction

 Share

Recommended Posts

darren lewis Apprentice

darren lewis

Posted
Posted
Do all rb25 heads including na use the same ports and bolt pattern for the intake and exhaust manifolds? Could i get a r32 rb25de head and put my r34 neo manifolds etc on it???

yes all the 25 head have identical intake patterns and ex patterns. yes the neo manifolds will fit same.

Link to comment
https://www.sau.com.au/forums/topic/254986-rb25-heads/#findComment-4408427
Share on other sites
bubba Grand Master

bubba

Posted
Posted (edited)

No.

Please know what you're talking about before you post.

The R32 RB25DE head has the same intake bolt pattern as the RB20DET. R33 RB25DET intake manifolds and R34 RB25DET Neo intake manifolds DO NOT BOLT UP.

Exhaust side, RB20/25/25neo are all the same.

To the OP, why would you want to get an R32 RB25DE head and put your Neo manifolds on there? if you're looking to build a 25/30 then you're better off sticking with the Neo head if you already have it :)

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/254986-rb25-heads/#findComment-4409378
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DraftySquash
      Installing the fuel sender O ring in R34 GTT

      By DraftySquash · Posted

      Another weekend and another project I have questions about.... I bought a fuel tank sender O ring to install on the car because I'm quite sus on what I've got now.  1. No "whooosh" sound when opening fuel cap 2. If I fill up full tank, there will be a small leak under the car and it comes from the top of the fuel tank, dripping along the side. Stops after a short while 3. Hot days = 50/50 chance to get high as a kite inside the cabin if the car was in the sun for too long This is what I bought: https://www.amayama.com/en/part/nissan/1734279900 My plan was to just replace the O ring but I've got some questions: 1. Does the whole fuel pump assembly need to come out for me to replace the O ring?         Or, could I unplug all the connectors and fuel lines at the top, take off the twisty part (17343) and put in the O ring from the top?  2. Is it a very common thing for everyone to just change the pump whenever doing this?        I see the Walbro 255 gets thrown in a lot but I've got no issues with my pump so far. When I did the tune, I asked the guy to check my fuel pressure and he said there were no issues too. But is it just a good idea to change to the 255 anyway as the old unit may have been in there for so long? The 255 seems to be a direct fit for GTT (I got no soldering iron)  
    • robbo_rb180
      Speedtek 800hp Close Ratio Gearset

      By robbo_rb180 · Posted

      Normal speedtek issues, bin it and go cdoo# or 8hp. So many issues with these gearsets, a mate went through 3 rebuilds and multiple parts with heat, bearing and vibration issues.  
    • Duncan
      CAM COVER BILLET HALF MOON RB RUBBER REPLACEMENTS

      By Duncan · Posted

      I wouldn't go near them, they are rubber seals for a reason. Just chuck new cam cover seals, half moons and the spacers for the screws every decade or two. I add a really thin layer of silicone too and it seems to hold together OK  
    • joshuaho96
      CAM COVER BILLET HALF MOON RB RUBBER REPLACEMENTS

      By joshuaho96 · Posted

      AFAIK on most Toyotas that half moon is usually an aluminum piece that you seal with RTV so you just source the valve cover gasket but I kind of doubt that you'll ever save money buying an aftermarket piece in this scenario.
    • TurboTapin
      Speedtek 800hp Close Ratio Gearset

      By TurboTapin · Posted

      If I tossed my money in a fire and filled my transmission with sand, it would end with the same result as buying from Speedtek. Actually, that's not true... My way, I wouldn't have to deal with Speedtek's dick head of a CEO for years on end and all his lies. 
×
×
  • Create New...